Smart Irrigation Infrastructure

Remote Water Pump Control — One Tap. Pump On. From Anywhere.

Custom-built control cabinets that put your water pump on the IOTMGR app — switch on, switch off, schedule, and monitor from your phone. No more morning and evening trips to the pump house. Built for any pump size, from 1 kW greenhouse pumps to 100+ kW industrial three-phase motors.

1 kW – 100+ kW Single & Three Phase IP65 Weatherproof Soft Starter Available 4G or LoRaWAN
Custom-built remote water pump control cabinet for agricultural irrigation, 4G or LoRaWAN connectivity
Why You Need It

Stop Driving to the Pump House

Most farmers visit the pump house 2–4 times a day, every day. Remote pump control eliminates those trips — letting you start, stop, and monitor pumps from wherever you are.

One Tap

Start Your Pump from Bed

No more 5 AM trips to the pump house. Open the IOTMGR app, tap once, the pump starts. Tap again, it stops. The whole irrigation cycle controlled from your phone.

Schedule

Run on a Schedule

Set daily, weekly, or seasonal pump schedules in the app. Off-peak electricity? Nighttime irrigation? Drought-restricted hours? Set it once, the cabinet handles the rest.

Monitor

Know Your Pump Is Running

Real-time status in the app — running, idle, or fault. If the pump fails to start or trips overload protection, you get an alert immediately, not when you find dry crops the next morning.

How It Works

Phone to Pump in 3 Steps

Your phone speaks to the control cabinet over 4G or LoRaWAN. Inside the cabinet, an industrial contactor switches the pump's high-voltage circuit on or off. The cabinet handles all electrical protection, surge handling, and motor management.

Your Phone Tap "Start Pump" 4G / LoRa Control Cabinet Receives + Switches High-Voltage Power Water Pump Starts pumping Total latency: typically under 2 seconds from tap to pump start
What's Inside

Industrial-Grade Components, Scaled to Your Pump

Same remote control experience, three internal configurations based on your pump's power requirements. Below: real customer cabinets we've built for small, medium, and large pumps.

Internal components of small pump controller for 1-3 kW single-phase pumps with air switch, contactor, DTU, and DC adapter

Small Configuration

1 – 7.5 kW Single-Phase Pumps

Internal components of medium pump controller with 220V air switch, contactor, IoT modem, water leak detection, and external antenna mounting

Medium Configuration

7.5 – 15 kW Pumps

Internal components of large pump controller with soft starter, dual air switches, DTU data module, and cooling fan for industrial three-phase pumps

Large Configuration

15 kW+ Three-Phase Industrial Pumps

What's Inside the Cabinet — Scaled to Your Pump

Every cabinet shares the same core building blocks — power protection, motor control, and IoT connectivity. What changes is the core driver that controls the pump motor: it steps up from a contactor to a soft starter to a VFD as your pump's rated power grows. Here's exactly what goes inside at each power level.

Component1 – 7.5 kWapprox. 1 – 10 HP7.5 – 15 kWapprox. 10 – 20 HPAbove 15 kWapprox. 20 HP +
Stainless Steel Enclosure (IP65, Lockable)Lockable stainless steel cabinet rated IP65 — sealed against dust and water jets, and built to survive sun, rain, and outdoor field conditions.✓✓✓
Main Protection BreakerMaster power cutoff with overload and short-circuit protection; rated higher as pump power rises.MCBMain air switchMCCB
Core Motor DriverSwitches and controls the pump motor — the part that changes most as your pump gets bigger.AC contactorSoft starterVFD
DTU / IoT Modem (+ Antenna)Receives commands from the IOTMGR cloud over 4G or LoRaWAN and reports pump status back.✓✓✓
Control-Circuit PowerA DC adapter and a dedicated control breaker that power the modem, kept isolated from the high-voltage side.✓✓✓
Cooling FanForced-air cooling for the soft starter or VFD in higher-power cabinets.—✓✓
Main Terminal BlockHeavy-duty connection points for incoming three-phase power and outgoing motor cables.——✓

✓ included  ·  — not required at this power level

Built for Your Pump

Custom-Configured for Your Exact Pump

Because pump motors vary by power rating, phase, and starting characteristics, every control cabinet is built around your specific pump. To get an accurate quote, send us the information below — most of it is on your pump's nameplate.

Power

Pump Rated Power

In kW or HP. The nameplate value, not the consumption value. This determines the size of the contactor, whether a soft starter is needed, and the enclosure size.

Phase

Power Supply Type

Single-phase 220V or three-phase 380V/415V. Single-phase is typical for residential and small agricultural pumps; three-phase is used for industrial pumps above 4–5 kW.

Network

Connectivity Preference

4G cellular (works anywhere with mobile signal) or LoRaWAN (requires our gateway, but works as part of a larger farm network with hundreds of devices on one gateway).

Pair with Smart Valves

Pump + Valves on the Same App

A pump control cabinet on its own gets you remote start/stop. Combined with smart valves downstream, you control your entire irrigation system from one app: open the right valves, start the pump, monitor flow, close the valves, stop the pump — all from your phone, in any order. Browse our smart valve range below to complete your system.

Frequently Asked

Common Questions About Remote Pump Control

Quick answers about ordering, capabilities, and pump compatibility. For project-specific quotes, contact our sales team with your pump nameplate.

Can I really start my water pump from my phone?

Yes. Once installed, you can switch your pump on or off from anywhere with an internet connection — through the IOTMGR app on your phone.

No more morning and evening trips to the pump house. You can also schedule pump cycles, monitor running status, and receive alerts if anything goes wrong.

What size pumps can you support?

We custom-build cabinets for any pump size, and the internal driver scales with your pump's rated power:

• Small (1 – 7.5 kW, approx. 1 – 10 HP) — an AC contactor switches the pump
• Medium (7.5 – 15 kW, approx. 10 – 20 HP) — steps up to a soft starter
• Large (above 15 kW, approx. 20 HP +) — uses a VFD

The internal configuration changes with the pump, but the remote-control experience stays exactly the same.

Do I need a soft starter for my pump?

A soft starter becomes the core driver for pumps from 7.5 kW (≈ 10 HP) up to 15 kW. Below that, a contactor and DTU switch the pump fine.

The soft starter ramps the motor up gradually instead of slamming it to full power — which prevents:

• Water hammer in pipelines
• Electrical surge stress on your grid connection
• Premature motor wear from repeated hard starts

Above 15 kW, a VFD takes over this role entirely and adds continuous speed control on top.

Do I need a VFD?

It depends on pump size:

• Large pumps (above 15 kW / ≈ 20 HP) — required. Big motors can't safely start or run without controlled speed, so a VFD is a safety and protection necessity.
• Small pumps (1 – 7.5 kW / ≈ 1 – 10 HP) — optional. The pump runs safely without one, but you can add a VFD for constant pressure across zones, energy savings, and gentler operation.

VFD sizing is forgiving — slightly oversizing it is common, accepted practice — so you can finalize the exact pump later without painting yourself into a corner.

What's inside the pump control cabinet?

Every cabinet shares the same core building blocks:

• Stainless Steel Enclosure (IP65, lockable) — sealed against dust and water jets for outdoor field conditions
• Main Protection Breaker — overload and short-circuit protection, rated higher as pump power rises
• DTU / IoT Modem with Antenna — 4G or LoRaWAN connectivity to the IOTMGR cloud
• Control-Circuit Power — DC adapter and a dedicated control breaker, isolated from the high-voltage side

The core motor driver changes with pump power: an AC contactor for small pumps, a soft starter for medium pumps, and a VFD for large pumps. Higher-power cabinets also add a cooling fan, and large three-phase cabinets add a main terminal block.

How do I order a pump control cabinet?

Because each cabinet is custom-built for your specific pump, send us your pump nameplate or specifications and we'll quote a complete solution.

We need to know:

1. Pump rated power (kW or HP)
2. Power supply type (single-phase 220V or three-phase 380V)
3. Connectivity preference (4G or LoRaWAN)

Contact our sales team with your pump details and we'll send a complete quote.

Not sure which configuration you need?

How to Choose the Right Remote Pump Control for Your Pump

A 10-minute guide: find your pump's rated power, match it to the right cabinet, and decide whether you need a VFD — explained for first-time buyers.

Read the Guide →

Get a Quote for Your Smart Valve Project

Share your pipe sizes, farm size, and deployment needs — our engineering team will respond with model recommendations and a project-specific quote within 24 hours.

Want to see how this fits into a complete smart irrigation system?

Read our Complete Guide to Smart Irrigation Valves — covering how the system works, real ROI from 30+ country deployments, and how to configure it for your farm.